Smoke sensor with WiFi IP camera and integrated battery is the ideal product for guarding corridors, cellars, offices or warehouses .
With an integrated high-capacity battery and motion sensor, the hidden camera can last up to 15 days! There is no need to bring any cables to the sensor , and installation is very simple and fast.
The camera is equipped with a super fast activation feature. Recording is activated for 2 seconds after motion detection. Mobile notifications will usually be received in less than 45 seconds from object intrusion.
Function:
- record in HD resolution
- up to 15 days of motion detection (PIR) or up to 20 hours of continuous recording
- Simple installation without cables
- motion detection recording mode using PIR / continuous recording
- simple smartphone application control
- wide angle of view (140 °)
- diode switch off via smartphone application
- the camera scans vertically
The UltraLive product range is characterized by a very long battery life and is hardly looking for comparisons in its category.
Extra long stamina
The UltraLife WiFi camera in the smoke sensor lasts for up to 15 days from its own battery.
Remote monitoring over a mobile phone
Watch your subject from anywhere. Just connect your camera to your local WiFi network, which will allow you to transfer the image over the Internet for an unlimited distance.Download the app from Google Play or the App Story, where you can easily view and change the camera's image.
Very wide angle of view
With a 140 ° angle of view, the hidden camera will scan the entire room without any problems. Ordinary minikamers with a pinhole lens do not reach even half the width of the shot as a Secutron UltraLife WiFi camera in a smoke sensor.Super fast activation
The smoke sensor uses a state-of-the-art camera module that takes up to 2 seconds to activate and start recording from PIR mode (economy motion detection mode).
Your WiFi connection takes less than 45 seconds, during which you also receive a notification about your mobile phone.
Motion Detection with PIR Sensor
Thanks to an integrated PIR sensor, the camera has very little power in motion detection mode. Camera performance per charge reaches up to 15 days .
Fast assembly without screwdriving and cable guide
You can easily install the smoke sensor using the attached 3M Dual Lock Velcro fasteners found inside the package.
Sample from smartphone app
Package contents:
- Secutron UltraLife WiFi camera in smoke sensor
- remote control
- 9000mAh battery
Ok, first what you need to set is SIM card: APN, User name and PASS.
As example I wrote: internet, izimobil, izimobil.
here:
Command:
AT+GTBSI=gl300,internet,izimobil,izimobil,,,,,FFFF$
Now set, “report mode”, APN, user name and pass must be written automatically, then IP and Port
Command:
AT+GTQSS=gl300,internet,izimobil,izimobil,3,,1,193.193.165.166,20706,
Also its important to set “Fixed report information” I done as example “Fixed time report” check every 30 sec, and send every 60 sec.
Command:
AT+GTFRI=gl300,1,0,,,0000,0000
These are most imporant steps to make start work GL300.
Please open manage tool you have from us and generate these commands by your self, after its set, you copy command from line and send SMS to GL300.
Please make sure that SIM card PIN is disabled and that your SIM card supports SMS.
Other important steps is create unit in GPS-trace platform, write IMEI and set that device is GL300.
Kind regards,
GL does not have such function to send SMS with alarm then it starts to move.
You can only get report to server then GL detects movement, here
AT+GTNMD=gl300,5,2,3,2,300,
1. QUESTION:
For tracking refresh i send to 20 sec but cars still go off the road:AT+GTFRI=gl300,1,0,,,0000,
should i set to 15 sec:, it is 20sec in still not on the road
1. ANSWER:
If GL is all time in the car and you need nice track, you can enable corner report
Command:
AT+GTFRI=gl300,,,,,,,,,,,,,,,,
I delete all other parameters, so it will be changed only corner, others will be as its set.
2. QUESTION: i have one client with complains reporting that tracker cost him a lot of costs, on sim card. what can he changes in settings?
2. ANSWER:
For the client which complains.
You can also send this command
AT+GTNMD=gl300,1,2,3,2,300,
This command is used, that if GL300 detect no movement, it will not report, after unit detect movement, device will start to report again.
sledilnik GL300« Nazaj
Šifra SKU: SPY300GPS
Naša šifra: 301
- Vgrajeni sistemi GPS in GLONASS
- Vodoodporna in udobna oblika
- Učinkovita baterija - do 60 dni
- Spletni dostop ali dostop do podatkov SMS na vodoodporni GPS sledilnik
- Združljiv z vsemi GSM omrežji
Brez naročnin in skritih stroškov!
|
Komplet vsebuje |
| Dimenzije |
| Filtriranje signala | |
| Ojačevalec filtrira izhodno frekvenco, katero oddaja notranja antena, na višjo frekvenčno lego in se s tem izogne medsebojni osilaciji. |
| Lastnosti |
